Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
holder4plumbing (TN)
Anyone have any experience/opinions about this particular valve? My kitchen sink plumbing has no shutoffs, and I am considering these to attach these (they attach with 3/8" female compression) where the kitchen faucet lines are currently connected, so as to add shutoffs without dismantling any existing plumbing. Found these at the big box store... Also, if anyone can explain how the female compression works on these. (Also, the directions don't say, but I presume the standard finger-tight then 1/4 to 1/2 turn). Thanks.
Edited 1 times.
|
Post Reply
|
Author:
packy (MA)
i'm assuming they are 5/8 compression by 3/8 compression stops ??
cut the copper tubing neatly, slide on the nut and ferrule, put a dab of grease to help tightening and crank away on them until they are pretty tight. two wrenches..
the top will take a flexible connector from the stop to the faucet. get good quality stainless connectors. those you don't overtighten to the stop.
|
Post Reply
|
Author:
holder4plumbing (TN)
on the input side, it's a 3/8" female compression, with a captured nut, which is tightened onto the output side of an existing shutoff (a way to replace a faulty shutoff without removal) or in my case to where the existing line has a compression fitting. I saw another brand on A---- (Watts LFPBQTR-615 Quarter Turn Retrofit) with great reviews but seems that it's out of stock, as the seller sent me another brand (ProLine). To see a picture of the Keeney, on A---- search on "Keeney 2072PCLF 3/8-Inch O.D. Captured Nut by 3/8-Inch O.D. Lead Free Quarter Turn Straight Repair Valve" for a picture of it (shown attached to an old shutoff).
|
Post Reply
|
Author:
packy (MA)
that will work. just a touch of grease on the male threads of the old valve to make them slippery and tighten quite firmly. i use a 5/8 open end wrench on those nuts. if it leaks make it tighter.
|
Post Reply
|
Author:
hj (AZ)
No picture but he seems to be describing a 3/8 x3/8 comp/comp "add a valve", which should work depending on how the sink is connected.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|