Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
didionkh (FL)
Searched the forum, got close but not quite what I was looking for.
Bought a house a few months ago. We're on Muni water but there's a softener here. It has not been used in 15+ years. I'd like to remove it, and the house is new enough to be plumbed with PVC/CPVC so it appears to be an easy enough job.
There is a shut-off valve in line and it is currently closed/bypassed (as much as I can get it shut. It has corroded over the years).
Question, can I just cut can cap the in/out pipes, or do I have to loop them?
|
Post Reply
|
Author:
hj (AZ)
how about a photo of the softener connections so we can answer that question?
|
Post Reply
|
Author:
didionkh (FL)
From the wall, In to a shutoff valve, to the in side of the softener. Out of the softener to a spigot, back into the wall:
[@#$%&[postimage.org]][/url]
Standard plastic hand-tightening compression connections at softener:
[@#$%&[postimage.org]]
|
Post Reply
|
Author:
hj (AZ)
You are kind of miserly with your photo, so I cannot tell if there is an integral bypass next to those nuts, but if not, you have to reconnect the two pipes together.
|
Post Reply
|
Author:
North Carolina Plumber (NC)
You won't be able to cap the pipes, either cut them and tie them together or put the service valves in by-pass mode, if applicable.
|
Post Reply
|
Author:
didionkh (FL)
Tell me what you need to see a pic of and I'll take more. The back of the softener head?
|
Post Reply
|
Author:
didionkh (FL)
NC Plumber, thanks. I'm in Florida, and this is in the garage. The in/out comes from the ground outside, through the garage wall, then in/out of the softener. If I need to tie the in/out together, I'll do it outside the garage to free up the (minimal) space a loop would have in the garage. Thanks again.
Edited 1 times.
|
Post Reply
|
Author:
hj (AZ)
yes, and wherever they "disconnected" to run to the softener is where you want to take it apart and reconnect the piping there.
|
Post Reply
|
Author:
srloren (CA)
You must have low water pressure to be using pvc. What is your pressure from the street?
|
Post Reply
|
Author:
hj (AZ)
It looks like CPVC, not PVC, which is proper.
|
Post Reply
|
Author:
didionkh (FL)
No clue what it is from the meter at the street, but it's 60 at all outside spigots.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|