Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
ddbbp (KS)
The only way I could get a new pump to stand straight in the pit was to position the pump where water dripping from into the pit is falling directly on top of the pump.... silly question, I know its a submersible pump but is there any harm in having the water flow fall directly on top of the pump?
Also I drill a 3/16th hole in the discharge as intended. Never done that before with a sump pump but the directions called for it. Water sprays out of it with force when the pump activates. Is that normal? Its splashing right against the the plastic wall of the basin and now I have to cover the top much better.
|
Post Reply
|
Author:
packy (MA)
the hole should be drilled at a 45 deg angle downward to direct the spray.
water falling on a submersible pump will do no harm.
|
Post Reply
|
Author:
hj (AZ)
You can use a hose clamp to hang a piece of rubber over the hole so the water sprays downward.
|
Post Reply
|
Author:
ddbbp (KS)
I wished they would have mentioned the downward drilling method in the installation instructions!
So if its OK for water to flow on top of the pump how about this....
is it ok for water to flow on top of the float?
In this case its not a tethered one rather the one that moves up and down on the rod.
|
Post Reply
|
Author:
packy (MA)
a small amount trickling onto the float would at most change the on/off cycle infinitesimally.
|
Post Reply
|
Author:
ddbbp (KS)
In heavy rain conditions water comes in at more than a slight trickle. Do you think that turbulence if allowed to land directly on top of the float would cause premature switch failure or otherwise hinder In the floats ability to do its job?
Every pump that I have installed I have always tried to allow the stream of water not to touch the top of the pump. I fear the water being close to the where the cord is attached.
I just cant do it any other way with this new pump.
In the past it always sounded like someone was taking a wiz in my basement since the trickle would always be hitting water.... allowing the water to hit the pump instead it is now silent.
Edited 1 times.
|
Post Reply
|
Author:
KCRoto (MO)
I usually position the hole to spray directly at the float when I put mine in so it can wash any debris and dirt off of the float.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor: