Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
jbmarkham (AZ)
We have a house built in 1942 with original plumbing fixtures, which drip. We've had two different plumbers replace gaskets ( I think ), which stops the dripping for about a month. They blame cheap Chinese parts. I wonder if there is another solution. My brother-in-law mentioned a deburring tool. What do you know about that and if there are higher quality parts available. We do have hard water. Please advise. Thank you.
|
Post Reply
|
Author:
KCRoto (MO)
While the quality of replacement washers for compression stems does vary, the main cause of deterioration is a seat that is rough or pitted. If the seats are replaced or resurfaced, it can last much longer between washer replacements.
|
Post Reply
|
Author:
hj (AZ)
How about a picture of the faucets you are working with.
|
Post Reply
|
Author:
Wheelchair (IL)
Knowing which brand of faucet you have is paramount to resolving the drip issue.
Pictures will help us to help you.
Best Wishes
|
Post Reply
|
Author:
jbmarkham (AZ)
Thank you for responding. Is the deburring tool meant to resurface the seat ? Some of the plumbers I've spoken with are not familiar with this tool.
|
Post Reply
|
Author:
jbmarkham (AZ)
I'll see what I can do. Thanks for responding.
|
Post Reply
|
Author:
packy (MA)
a plumber that is not familiar with a seat grinding tool?
where did you find that plumber, venus??
|
Post Reply
|
Author:
hj (AZ)
IT is a "last ditch" tool to use on the seats, because if it is NOT used properly, it will make the seat worse than you started, and might have to throw the faucet away. Still need pictures.
|
Post Reply
|
Author:
hj (AZ)
You are assuming ALL plumbers are competent to do service repairs. Bad assumption, especially with the new crop that only know how to replace things, because they get a bonus when they do.
|
Post Reply
|
Author:
jbmarkham (AZ)
I'll get them as soon as I can. Thanks for your help.
|
Post Reply
|
Author:
jbmarkham (AZ)
California....in same orbit with Venus. I'm not letting anyone grind/deburr anything until I know they are experienced and preferably old, like our faucets. Thanks for your help.
Edited 1 times.
|
Post Reply
|
Author:
KCRoto (MO)
Some seats are replaceable and you can simply unscrew the old seats and install new ones. If it is possible, I would recommend trying that route first.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|