Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
hospcfo (KY)
Been having this problem for a couple of weeks now. Both hot and cold will continue to run slowly for a few seconds after shutting the valve off. I also had lower pressure than normal for awhile but cleaning the aerator fixed that. It's a two handle faucet with spray hose. I got new valves at Home Depot and replaced both sides but no change. The valves have a white plastic body with brass stem.
Any suggestions are appreciated before I move on to a new faucet .
|
Post Reply
|
Author:
hj (AZ)
It is probably pressure build up and then drain down in the spray hose.
|
Post Reply
|
Author:
Fixitangel (NC)
On alot of Delta faucets the culprit is the rubber seals and springs down in the bottom of the valve body that need to be rpl. DL-9 is a common set. The valve cartridge body rarely fails.
I use a skinny phillips screwdriver to slip the new seals and springs onto, apply a little dab of plumbers grease to the seal, stick the end of the phillips into the seat and slide the new parts off the shaft and into the seats. With a little luck, they will line up where they can be pushed into the "hole" and pressed down into position.
|
Post Reply
|
Author:
hj (AZ)
You can also use a tire gauge. Pull the stem out, slide the seat and spring on to it, stick it into the hole and then push the gauge down to set the seat into the faucet.
|
Post Reply
|
Author:
hospcfo (KY)
Thanks. After replacing the valves I removed the spout, cleaned it up a bit and re-assembled and now all is well (for now anyway). I actually bought the parts you show initially but when I took the valve out I didn't see the spring. It's not inside the valve assembly, I expected to see them in the housing that the valve slides into. But I couldn't feel them nor see them using a flashlight, maybe I just missed them. Do all Deltas have those?
|
Post Reply
|
Author:
KCRoto (MO)
Unless the cartridges have been replaced with ceramic cartridges, yes.
|
Post Reply
|
Author:
Fixitangel (NC)
If your faucet has these, you will not see the spring when you pull the cartridge. It is hidden under the rubber seal in the bottom of the valve body.
|
Post Reply
|
Author:
hj (AZ)
ALL Delta springs are hidden in the valve body under the rubber seal.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|