Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
besasse (TX)
A plumber is trying to install this faucet that I bought many years ago. The supply tubes that screw into the bottom of the faucet are missing. They must have a 7/16" or 11mm male end. American Standard, who sold Porcher (now out of business) has been no help on this.
|
Post Reply
|
Author:
hj (AZ)
Normally, they would have an "O" ring seal where they screw in and would be specific to that faucet. If so, you would have to find a parts company that could supply them, assuming they still exist.
|
Post Reply
|
Author:
packy (MA)
it would not have come with supply tubes. it would have come with 2 adapters to change from European thread to American thread.
|
Post Reply
|
Author:
hj (AZ)
I believe they are either referring to hoses between the valves and spouts, or flexible lines hanging from the valve to connect with the lines from the angle stops. The "adapters" were typically used between the faucet supply lines and supply lines from the angle stops, NOT at the valve itself.
|
Post Reply
|
Author:
besasse (TX)
Installation diagram shows 2 -3/8"od copper tubes extending from bottom of faucet. Compression fittings are provided for these for connection to 1/2" ips flex supplies or 3/8" bull nose risers.
Copper suppply tubes are the missing parts.
|
Post Reply
|
Author:
packy (MA)
if this is what you are looking for, there must be thousands of them out there
3/8 x 12 chrome lav supplies...
|
Post Reply
|
Author:
hj (AZ)
How about a copy of the installation pictures. The 3/8" supply tubes are probably threaded in to the valve body.
|
Post Reply
|
Author:
bernabeu (SC)
[www.porcher-us.com]
part #1 (supply adapters) are available from Am. Std.
part #2 (the actual faucet supply tubes) should have been factory installed and, unfortunately, may not be available
call: 1 (800) 359-3261
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Edited 1 times.
|
Post Reply
|
Author:
besasse (TX)
Supply tubes are not available from American Standard. Tubes have no part number. Have found no other source.
|
Post Reply
|
Author:
steve (CA)
There are supply tubes, with bare ends, that are factory attached to the faucet. They provide compression adapters, that compress onto the bare supply tubes and adapt the tubes to a standard 1/2" pipe faucet thread.
The adapter part number is - 028587-0040A
A google search found 1 seller of the adapter.
If the tubes are copper, can your plumber swedge them to 7/16"OD tube or solder 1/2"OD copper over them?
Edited 1 times.
|
Post Reply
|
Author:
besasse (TX)
Thanks Steve. I have the adapters and am missing the copper tubes.Maybe I can have these made.
|
Post Reply
|
Author:
hj (AZ)
quote; Maybe I can have these made
Very unlikely, and if possible, it will probably cost more than a new faucet.
|
Post Reply
|
Author:
steve (CA)
If the housing thread is 7/16 fine(24tpi) a ¼" bulkhead connector might work(there might not be enough circumferential room for the 2 connectors and whatever holds the faucet to the sink. The inlet to the connectors is ¼ OD, but with water conservation measures now, it might not make that much difference in what exits the spout. As already stated, there usually is an o-ring to seal an original tube connection like that, but a flat sealing washer with the bulkhead connector should seal ok.
|
Post Reply
|
Author:
besasse (TX)
Thanks Steve. Will pursue this possibility.
|
Post Reply
|
Author:
hj (AZ)
There may not be a "flat surface" to seal against inside the faucet. They usually drill a hole and then tap it for the supply line and the "O" ring makes the seal in the bore.
|
Post Reply
|
Author:
steve (CA)
I removed a Price Pfister widespread lavatory faucet today and the valves are connected to the spout with these hoses. One end is 1/8" straight pipe with an o-ring seal and the other end is 3/8" compression. 1/8" pipe is bigger than 3/8" and smaller than 7/16". These hoses are not under pressure all the time, like you need, but I would think they should be able to maintain constant pressure. Maybe use "flood safe" supply hoses with them?
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|