Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
roxald (Non-US)
Good day all, I am trying to install a T-fitting in my 3" horizontal line to connect a 1 1/2" drain pipe from my wet bar. Both ends of the 3" are fixed in concrete and I have about 4 feet of the 3" exposed to tie in. After I make the 1st cut to separate the 3" pipe, how to I spread the ends far enough apart to install the T-fitting?
Rox
|
Post Reply
|
Author:
hj (AZ)
quote; how to I spread the ends far enough apart to install the T-fitting?
Rox
That is an easy one to answer. You DO NOT, because you cannot do it. You have to use "repair" couplings, there are many different kinds, and drop your connection into the gap and then slide the couplings over the joint.
|
Post Reply
|
Author:
steve (CA)
What kind of "tee" fitting are you going to insert? Sanitary tee is not legal. You need a wye or combo tee.
I use shielded "no-hub" couplings for this type of installation.
Edited 1 times.
|
Post Reply
|
Author:
roxald (Non-US)
Thanks Fellas, that was my next option. The ones I've seen are a soft rubber shaped like an normal end to end fitting with a wide metal hose clamp across the entire width. I believe it is called a no-hub coupler?
Appreciate the quick response!
Cheers,
Rox
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
hj (AZ)
quote; I use shielded "no-hub" couplings for this type of installation.
Even though they will work, if it is going to be inspected, our inspectors want "specific" transition couplings labeled for the materials being used.
|
Post Reply
|
Author:
bernabeu (SC)
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
steve (CA)
Even when it's not a "transition" connection? Why use a coupling with 2 different IDs, when the pipes ODs are the exact same?
|
Post Reply
|
Author:
hj (AZ)
If it is for the correct materials, the i.d.s will be the same.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|