Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
billiardsteve (NJ)
Good Afternoon,
I'm new to plumbing and have hit my first snag. I'm working in a tight space between 6" joists and I'm trying to figure out how to connect some ABS drain lines in a manner that will pass code.
My first question is whether it would be within code (or advisable) to connect a 45 deg street into the end of a long sweep going back the other direction, almost creating an S-curve.
My second question is whether any manufacturer makes a 3x2x3 wye. The branch of the wye is always the reduced size in everything I come across.
_3
__\
2----3
Thanks so much for the help. Other posts on this forum have been incredibly helpful.
Steve
|
Post Reply
|
Author:
packy (MA)
if you mean create a 135 deg turn in a drain? well, i wouldn't..
as for the "Y" in question, could a 3 x 2 bushing in the end of a 3 inch "Y" do it?
|
Post Reply
|
Author:
billiardsteve (NJ)
Not a 135 degree turn, a 90, then back 45 the other direction.
Unfortunately, with my space constraints, a typical 3x3x3 wye with a reducing bushing is too big for the space. Unless someone knows of a manufacturer of special short wyes. I'm working in between joists at a tough angle.
Thanks,
Steve
|
Post Reply
|
Author:
hj (AZ)
quote; Not a 135 degree turn, a 90, then back 45 the other direction.
Usually, in that situation, a 45 without the 90 would do the same job.
|
Post Reply
|
Author:
bernabeu (SC)
"T" type fittings are always specified as RUN-RUN-BULL
so you are looking for a 3(run) x 2(run) x 3(bull/branch) "Y" fitting
no such animal available for 1 piece purchase
you can use a 'flush'/internal 3x2 bushing on a conventional Y
(just cut off the hex 'shoulder' after gluing in if necessary - you will then have a 3x2x3 with the exact dimensions of a 3x3x3)
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
hj (AZ)
The bushings at my supply house are flush without the hex shoulder. You do want to check the direction before you glue them in, because they do have a stop on the bottom.
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|