Welcome to Plbg.com
Thank you to all the plumbing professionals who offer their advice and expertise

Over 705,000 strictly plumbing related posts

Plbg.com (aka: PlumbingForum.com) where plumbing help, advice, education, information, and plumbing related suggestions are provided FREE by some of the most experienced plumbing contractors and plumbers anywhere who all wish to "give back" to society. Since 1996 we have been completely free of popup advertising or any other invasive ads and have been known to be the best online STRICTLY PLUMBING advice and help site. You've come to the right place IF you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. We absolutely do not sell your personal information. We are made possible by:  

Post New
Search
Log In
How to Show Images
Newest Subjects
 PVC to shutoff valve connection
Author: GADIYer (GA)

Hi,

I'm trying to replace the leaky shutoff valve in my home but I'm having problems removing it from the PVC pipe used to supply the water to the house. The PVC pipe has a male fitting attached to the end to which the shutoff valve screws directly into. I thought since it was threaded that I would be able to remove it but it is not budging and I'm afraid to put too much force into it for fear I'll end up cracking the rest of the pipe. Is this fitting not reusable? I was under the impression that you normally only need to use teflon tape to join metal to this PVC fitting but it feels like it was glued.

Any ideas, advice or suggestions?

Thanks!



Edited 1 times.

Post Reply

 Re: PVC to shutoff valve connection
Author: steve (CA)

The fitting should be reusable. If you have a wrench on the fitting, to prevent the rotational force from trying to rotate the pipe, that fitting might snap, but the pipe should be ok. The only other thing would be to cut slit(s), parallel to the centerline, in the perimeter of the valve and try and relieve some pressure from the threads.

Post Reply

 Re: PVC to shutoff valve connection
Author: GADIYer (GA)

Thank You Steve!

I was not using a wrench on the fitting ( holding the pipe in place to keep it from twisting ) because I was worried I'd mess it up but as you pointed out, even if it was damaged, the pipe itself would still be okay and I'd be no worse off. I went ahead and did as you suggested and was finally able to break it free. The wrench chewed up the nibs on the fitting somewhat but it didn't appear to crack the fitting.

How many wraps of tape should I apply to the fitting when putting the new valve on?

Thanks again for your help, I really appreciate it!

Post Reply

 Re: PVC to shutoff valve connection
Author: steve (CA)

Usually, three wraps is what is recommended. There are some people in the industry that feel that Teflon tape should not be used on plastic fittings and if anything is to be used, it should be a paste type sealant that is approved for plastic piping. Personally, I have no issue with the tape being used.

Post Reply

 Thank you clap
Author: GADIYer (GA)

Hi Steve,

Just thought I'd let you know the outcome. I ended up having to cut the fitting off the CPVC as there was a little seepage even after tightening down the new cutoff valve as far as I felt comfortable doing. I really didn't want to do that and ultimately shortening the incoming pipe but I had to get it done. Maybe I did end up cracking the fitting in a place that wasn't obvious to me when I removed the old shutoff valve.

Anyway, I got it fixed with a new shutoff valve and a new PRV since I was already there and the existing one had been on there for at least 20 years.

Thanks again for your help!



Edited 1 times.

Post Reply

 thumbs
Author: steve (CA)

Thanks for the update.



Edited 1 times.

Post Reply





Please note:
  • Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
  • Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
  • Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
  • Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.

Search for plumbing parts on our sponsor's site:




Special thanks to our sponsor:
PlumbingSupply.com


Copyright© 2025 Plbg.com. All Rights Reserved.