Over 700,000 strictly plumbing related posts
Welcome to Plbg.com (also known as PlumbingForum.com) where plumbing advice, education, information, help and suggestions are provided by some of the most experienced plumbers and plumbing contractors anywhere who all wish to "give back" to society. Since 1996 we have been free without popup or other invasive ads and known to be the best online STRICTLY PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't track you. We absolutely do not sell your personal information. We are made possible by:
Author:
MES (PA)
I have noticed lately that the water pressure seems reduced a bit inside the house when using more than one water source (eg washing clothes while taking a shower at same time or taking a shower while running the kitchen faucet etc).
I thought I even noticed the shower water reduced for a few minutes a bit while taking a shower and didn't think anyone was using any other water source in the house, as well.
The tag hanging on my watts water pressure reducing value says it is set at 50 PSI and the range says 25-75 PSI. I connected a water test pressure gauge on the outside of my house and it said 50 PSI with no water running inside the house.
I checked the gauge again outside after turning on the kitchen faucet and it went down to 40 PSI.
I should have tested it after turning on 2 faucets inside the house or flushing the toilet, but didn't think of it at the time. I am sure it would have tested below 40 PSI. I am not sure what the issue is.
Should I just increase the PSI on the value by turning the screw on top it clockwise by about 1/4 of a turn?
Any input would be helpful.
Thanks.
Edited 1 times.
|
Post Reply
|
Author:
packy (MA)
most pressure regulators have a filter screen on the inlet side to keep debris out of the valve. if you can figure out how to access the filter then that is what i would do first. if you can't figure it out, post a picture or two of what you have and somebody will give you advice.
i'm not saying 100% its clogged, i'm saying that is the first thing i would look at.
|
Post Reply
|
Author:
MES (PA)
Hi packy. This is the watts water pressure reducing value that I have. I provided a link of it below.
[www.watts.com]
|
Post Reply
|
Author:
steve (CA)
There is a strainer built into the regulator. You would need to unscrew the bell and remove the internals to inspect the strainer.
|
Post Reply
|
Author:
packy (MA)
from their website ..
. It consists of a Lead Free* brass body construction ---integral stainless steel strainer---, thermoplastic seat, bronze sealed spring cage for waterworks pit installations and thermal expansion bypass
|
Post Reply
|
Author:
MES (PA)
Is removing the bell and getting to the strainer not too difficult to do for someone who is far from an expert at this stuff?
|
Post Reply
|
Author:
steve (CA)
I don't know if you remove the entire regulator, if you can see at least a small portion of the strainerthrough the inlet port. Otherwise remove the bell.
|
Post Reply
|
Author:
MES (PA)
After unscrewing the top to remove the bell, is it easy to just lift out the value assembly and to place it back in? I just to make sure before I attempt it having never done this before.
|
Post Reply
|
Author:
MES (PA)
Also, do I need to shut off the water line that is coming directly into the house before doing this, even if, nobody will be using water in the house? If so, I just hope that does not leak if I try to turn it off, since it is not used much.
|
Post Reply
|
Author:
steve (CA)
Yes, the incoming water needs to be shut off and there might be water draining down from the house piping. The internals should just pull out. There are o-rings that might give some resistance to pulling out the internals.
|
Post Reply
|
Author:
MES (PA)
I did not attempt to pull apart my pressure reducing value yet. Having never done that before, I don't want to start pulling it apart without really knowing if it is difficult to put it back in place. I don't thik the issue I will describe now has anything to do with the value. When I turn the water on in my bathtub, the water comes out fine through the tub spout, but when flip it to have it come out of the showerhead, the water barely comes out. Once in awhile the water pressure will become a bit stronger, but after a minute or 2, it goes back to a tiny sprinkle. What could be the cause of this?
|
Post Reply
|
Author:
sharp1 (IL)
Shower heads can become clogged from hard water deposits. Remove the shower head and test pressure without it. If pressure is good, soak the shower head in white vinegar or CLR for 24 hours or so, flush with clear water, and reassemble and retry.
|
Post Reply
|
Author:
MES (PA)
I use a filter on my showerhead and I had just replaced it and the pressure wasn't strong from the beginning. I took off the shower head and the pressure was strong. I have another new shower filter and replaced it with a new one. The pressure was strong. The other filter was bad. Sharp1, thanks for the reply and help.
|
Post Reply
|
Author:
MES (PA)
Update, the pressure on my new filter turned out to be just as bad. I have read that issues with a water softener can cause water pressure issues. I noticed that my water starts to become hard half way and the last time it was less than half way through a cycle. Could this be the main cause of my pressure issues?
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|