![Welcome to Plbg.com](/images/plbg-forum-logo.png)
![Thank you to all the plumbing professionals who offer their advice and expertise](/images/plbg-thankyou-banner2.png)
Over 700,000 strictly plumbing related posts
Welcome to Plbg.com (also known as PlumbingForum.com) where plumbing advice, education, information, help and suggestions are provided by some of the most experienced plumbers and plumbing contractors anywhere who all wish to "give back" to society. Since 1996 we have been free without popup or other invasive ads and known to be the best online STRICTLY PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't track you. We absolutely do not sell your personal information. We are made possible by:
Author:
JTT (AZ)
Hi All! I hired a GC for Underslab plumbing and they tested the DWV at 5 psi. The pressure held for an hour then slowly dropped to 0 psi after 8 hrs. Is it normal to have 0 pressure after a period of time or could it be a possible leak? …I’m not sure about this. I read the AHJ requires DWV to hold 5 psi for 15 minutes. Thnx for any feedback, opinion!
|
Post Reply
|
Author:
hj (AZ)
IF the pressure held for over an hour, when only a shorter term is required, then it should have passed.
|
Post Reply
|
Author:
JTT (AZ)
Thnx for the quick reply! And that’s what I’m reading though I’ve not ordered the inspection yet. But the plumber said they’ll look for a leak as if some pressure should remain. I’d like to know if a DWV pressure test can read 0 psi after time (contrary to water supply lines) and not necessarily be an issue. Of course it’s my decision what caused drop in pressure, just need some input. Thnx again!
|
Post Reply
|
Author:
packy (MA)
you can always pump it up again and spray bubble water on the joints looking for bubbles.
|
Post Reply
|
Author:
bernabeu (SC)
The AHJ is looking for MINIMUM code.
What YOU want is good or best practice.
Of course there should be 'some' pressure left after 8 hours.
? Where did it go ? LEAKAGE
|
Post Reply
|
Author:
JTT (AZ)
Thnx packy. I tried that, didn’t notice anything. But pressure was low (2 psi) and I can’t test the section of pipe on the ground. …I may pressurize at 5 psi and try again.
|
Post Reply
|
Author:
JTT (AZ)
Great bernabeu! The info will help me make an informative decision. Btw Plumber will retest DWV system today which tells me 0 psi is problematic.
|
Post Reply
|
Author:
bernabeu (SC)
test it with a static 10 foot 'head' of water (approx 4.32 psi)
level/pressure should NOT drop at all
|
Post Reply
|
Author:
packy (MA)
every once in a while, my friend from SC shows brilliance.
if it is not practical to stand up a 10 foot tall pipe, simply do a hydrostatic test.
What Is Hydrostatic Testing?
Fill the pipeline with a liquid, mostly water, unless its material is incompatible with water.
Apply pressure to the pipeline to bring it to its acceptable test pressure. ...
Hold the pressure for a required timeframe to examine the pipeline for possible leakages.
|
Post Reply
|
Author:
bernabeu (SC)
the 10' pipe IS the hydrostatic test
hydro = water / static = no motion
a 'cheat' would be to fill with water, pressurize with 5 psi air FROM THE VERY TOP depressurize after 1/2 hour and see if the water level dropped AT ALL
that would be called a hydro-pressure test
|
Post Reply
|
Author:
JTT (AZ)
hydro-pressure test - Interesting!
Edited 1 times.
|
Post Reply
|
Author:
JTT (AZ)
Thnx bernabeu and packy for the suggestions! Yes, the plumber has conducted both tests (hydrostatic and air) but same result - failed. Avoidable mistakes like end cap leak or plug blows off the exit pipe. And to move expeditiously isn’t their strong suit. This GC’s workforce is spread too thin imo. …a 7 day project is now a month!
Anyway they’ll TRY to finish repairs and re-test today, I’ll update you….
Edited 2 times.
|
Post Reply
|
Author:
JTT (AZ)
The plumber arrived this morning and I thanked him! The system is pressurized at 6 psi (hydro-pressure test) and holding! I’ll watch it today and hope to call for tomorrow inspection.
|
Post Reply
|
Author:
bernabeu (SC)
it is the water LEVEL, not the AIR PRESSURE, which is important
the air PRESSURE will act somewhat like an expansion/compression tank and 'tend' to remain constant, especially if charged in the AM of a rapidly warming Arizona day
Open the topmost fitting, fill the system with water to the very top, add a nipple and valve, top 'er off with water, pressurize with a bicycle pump to about 4, close the valve, come back 'later' to see if the water LEVEL dropped.
|
Post Reply
|
Author:
JTT (AZ)
I’m sold on hydro-pressure test, a good way to find leaks. The plumber pressurized the system and a couple hours later I hand checked each pipe joint and found two leaks (water on my fingers). …very cool!
|
Post Reply
|
Author:
packy (MA)
since the probability of leaks (plural) is real, i would strongly suggest the plumber mixes a fluorescent dye into the water and then pressurizes the piping.
they will know what you are talking about.
the dye will make any leaks much easier to find.
[www.amazon.com]
funny story...
i knew of one inspector who would come out to the job, look at the gauge for five pounds and then ask to have something opened up so he could hear the air rushing out. yeah, some plumbers actually have a gauge that the hand is stuck on 5 PSI.
|
Post Reply
|
Author:
JTT (AZ)
Thnx packy for the dye suggestion and link. …I did mention it to the plumber. Anyway I’m at a standstill waiting for repairs and running out of time and patience!
Edited 1 times.
|
Post Reply
|
Author:
JTT (AZ)
Plumber is here! …let’s all pray and I feel lucky ![smile smile](https://www.plbg.com/forum/mods/smileys/images/smile.gif)
|
Post Reply
|
Author:
JTT (AZ)
Underslab DWV pressure test Passed!!
Thnx everyone for suggestions and encouragement. I’ll be back as I continue the build. Cheers
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
![PlumbingSupply.com](https://www.plumbingsupply.com/images/plumbingsupply.png)
|