Over 700,000 strictly plumbing related posts
Welcome to Plbg.com (also known as PlumbingForum.com) where plumbing advice, education, information, help and suggestions are provided by some of the most experienced plumbers and plumbing contractors anywhere who all wish to "give back" to society. Since 1996 we have been free without popup or other invasive ads and known to be the best online STRICTLY PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't track you. We absolutely do not sell your personal information. We are made possible by:
Author:
o2458NUEjHxmj9dcgkKA (TN)
I have a bathroom in the basement with normal sink and toilet plumbing going into the concrete slab. I want to add a corner shower. The sink drain is PVC and will be roughly 6ft from the shower drain. How high of a platform does the shower need to be on to have room for the P-trap? Can this be done without a pump?
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
you chop out the slab and install a solid trap designed for gasketed drain attachment from above
OR
you get a permit and a plumber
OR
[www.saniflodepot.com]
Edited 1 times.
|
Post Reply
|
Author:
packy (MA)
if i understand you correctly...
you want to tie the shower drain into the sink drain just as it enters the floor?
how this is done depends on the vertical section of the sink drain at the floor level.
if you break the cement floor where the shower trap is, you can recess the trap and probably get away with a 2x6 platform.
unless there is something really strange about the sink drain, no pump will be needed.
|
Post Reply
|
Author:
o2458NUEjHxmj9dcgkKA (TN)
Thank you for the reply.
[ibb.co]
This is the roughed in sink plumbing. It will be a corner sink and the shower drain will be in the wall that connects to the left of the stud. Was planning to turn left and tie in at the very bottom as the drain enters the floor.
If that final turn might be an issue, I could also move the sink to the left and connect to the drain without the last turn.
I have a full 8ft where the shower is going so a platform shouldn't be a problem. Would really like to NOT break the cement floor if possible.
|
Post Reply
|
Author:
packy (MA)
get a 2 inch p-trap, put it together (no glue), hold it next to the sink drain with the trap belly sitting on the floor. mark the center of the trap outlet on the sink drain. add 1/4 inch per foot of distance from the sink drain to the shower trap actual location. that will be the center of the sanitary tee you cut into the sink drain.
NOW you'll be able to calculate the depth of the shower platform.
you can decrease the height of the platform by breaking the floor and recessing the trap.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
![PlumbingSupply.com](https://www.plumbingsupply.com/images/plumbingsupply.png)