Over 700,000 strictly plumbing related posts
Welcome to Plbg.com (also known as PlumbingForum.com) where plumbing advice, education, information, help and suggestions are provided by some of the most experienced plumbers and plumbing contractors anywhere who all wish to "give back" to society. Since 1996 we have been free without popup or other invasive ads and known to be the best online STRICTLY PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
vbtalent (KY)
What the secret to installing kitchen sink slip nuts so that they don’t leak?? I just updated some plumbing under our sink and the the slip nuts are slightly dripping, it just doesn’t seem like I can tighten them enough.
Should I use some type of sealant in the threads, maybe Teflon tape or pipe dope…
These slip nuts had red rubber like gaskets as opposed to the hard clear ones I was used to seeing.
Any help would be appreciated.
BB,
|
Post Reply
|
Author:
george 7941 (Canada)
Alignment of the pipes is very important.
Get some clear rings/washers and see if that stops the leak.
|
Post Reply
|
Author:
vbtalent (KY)
Thanks for the reply.
Can I use some type of sealer in case I’m still struggling?
|
Post Reply
|
Author:
sum (FL)
no sealant is needed or even desirable.
check your washers to make sure the tapered side is inserted correctly.
|
Post Reply
|
Author:
packy (MA)
if you call it sealant it is not desirable.
if you call it lubricant it helps.
|
Post Reply
|
Author:
hj (AZ)
And, since the oil in "lubricants" can dissolve rubber, it might not be a good idea to use it.
|
Post Reply
|
Author:
bsipps (PA)
Plastic washer to plastic fitting connection usually means ( lubricant) may be needed
|
Post Reply
|
Author:
packy (MA)
silicone grease is actually good for rubber
|
Post Reply
|
Author:
sum (FL)
what about bacon fat or butter?
|
Post Reply
|
Author:
bernabeu (SC)
butter
bacon fat rots and stinks
|
Post Reply
|
Author:
vbtalent (KY)
So what would you use as a lubricant then for
plastic in plastic?
|
Post Reply
|
Author:
bernabeu (SC)
silicone grease
or, really, butter
|
Post Reply
|
Author:
vbtalent (KY)
Just wanted to close the loop and thank you for the advice.
The clear rings are the way to go..no leak, no grease, no looking back!
Thanks all!
VB,
Edited 2 times.
|
Post Reply
|
Author:
bernabeu (SC)
you are welcome
the plastic rings are wedge shaped and 'fill the gap(s)'
MERRY CHRIST MASS
and/or
HAPPY HOLIDAYS
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|