Radiator bleeding valve on very old radiator

Over 698,000 strictly plumbing related posts

Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:

Post New

How to Show Images

Newest Subjects

Radiator bleeding valve on very old radiator
Author: Amm1majus (NJ) Can anyone direct me as to where the radiator bleed valve is on this radiator? [postimg.cc]
Post Reply

Re: Radiator bleeding valve on very old radiator
Author: bsipps (PA) Usually located in the top left or right front for those old convectors The easiest way to get to it is to take the front cover off Edited 1 times.
Post Reply

Re: Radiator bleeding valve on very old radiator

Author: bernabeu (SC)

There is NO, repeat NO, bleed valve as the radiator is for one pipe steam.

The thermostatic 'bullet' about half way up vents air until it gets hot from the steam and closes.

Said radiator 'may', or may not, be capable of CONVERSION to hydronic heat.

Said 'bullets' come in varying capacities from A through (if memory serves) H, and also come in 'adjustable' versions (problematic at best).

Quote

In one-pipe steam installations, steam flows from the boiler to the radiators, where it displaces the cold air by pushing it out through a vent on the radiator. The air vent closes automatically when the radiator is full of steam. The heat energy in the steam is then transferred to the room, as this occurs the steam cools and condenses into water which pools at the bottom of the radiator. This condensate then flows back again through the same single pipe.

Due to the steam and water flowing in opposite directions through the same pipe, the diameter of this pipe is typically more than 1". So one-pipe radiators are easy to identify from the single, fairly large pipe connected to them, always at the bottom, and an air vent attached to the opposite side, typically halfway up the height of the radiator (see below).

[www.castrads.com]

==============================================

"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638

Post Reply

Re: Radiator bleeding valve on very old radiator
Author: ArthurPeabody (NM) heatinghelp.com has lots of experts ready to help with this sort of question.
Post Reply

Re: Radiator bleeding valve on very old radiator
Author: bsipps (PA) Bern you are correct I neglected to see the steam vent, pic quality was not so good
Post Reply

Re: Radiator bleeding valve on very old radiator
Author: packy (MA) i've never seen a cast iron radiator that was made for steam only ??? is there a second 1 or 1 1/4 inch tapping on the bottom somewhere ? you obviously need two tappings for hot water where as steam can work on only one.
Post Reply

Re: Radiator bleeding valve on very old radiator
Author: bernabeu (SC) THIS radiator APPEARS to be some sort of custom casting. It does not seem to be sectional. ============================================== "Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Post Reply

Please note:

Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.

Search for plumbing parts on our sponsor's site:

Plbg Advisor List Common Plumbing Terms Find A Plumber Plumbing Manufacturers Directory theplumber.com

Special thanks to our sponsor:

to FAQ's - to popular subjects - to plumbing books - to Tankless 101 - to plumbing history - to helping charities - to contact us