Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
nocriz (WI)
Hi,
I am based in Wisconsin and trying to finish my basement. During the process, I wanted to add a bar sink at a location. In order to plumb everything correctly, I needed advice.
The sink for the bar is about 12 - 13 feet from the nearest drain pipe which has been provided for a sink in a half bath. Half bath has a rough in for a toilet too and a three inch drain pipe close by.
Here are my questions -
1. Can I connect the bar sink drain pipe to the 2 inch wet vent pipe provided for the sink in half bath? How would I provide a vent for the bar sink?
2. If yes, how would I go about connecting the bar sink drain pipe to the bathroom sink drain?
3. Do I need to have a vent line for the toilet too which I would have to connect to the 1.5 inch vertical pipe provided for sink in half bath? Is that needed and or allowed?
4. If the toilet needs to be connected to the 1.5 inch pipe then are three connections allowed on the vertical pipe?
I would really appreciate any advice regarding the matter above.
-Tj
[i.postimg.cc]
[i.postimg.cc]
[i.postimg.cc]
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
Option 2 is the proper principle to vent the new sink
BUT
the vent needs to turn the corner and run around the wall at the shown elevation THEN drop down to the drain in the wall near the trap.
ELSE, because of the pitch and length of the run, you would have an unvented 's' trap.
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
packy (MA)
option three (if your code allows it) is to turn the corner run the drain to the sink and use an AAV under the counter.
if not allowed, follow my friend from SC's advice.
|
Post Reply
|
Author:
Lorensr (CA)
I would plumb it this way. [postimg.cc]
Use Sanitary Tees. 2"x1 1/2" where you tie in and 1 1/2" for the bar sink. The HVAC volume will be minimal. Use MS elbows.
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
option 3 still requires the vent to be tied in 'upstairs' somewhere
IMO:
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
packy (MA)
what vent are you talking about?
|
Post Reply
|
Author:
bernabeu (SC)
packy,
i 'mis-spoke'
not option 3 which is an AAV ('legal'), but, IMO: not good practice if avoidable
i was refering to 'i would plumb it this way' ~ [postimg.cc]
i erred, again, and soon into the new year
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|