Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
DorkyJen492 (WA)
My home's gas water boiler broke after 30 years (original) and am looking to replace it. I noticed that I have two options: condensing (+90% AFUE) and non-condensing (~80% AFUE) boiler. I am leaning towards getting a non-condensing boiler because:
* Non-condensing boiler is cheaper to purchase and install
* Non-condensing boiler is less complex (minimal computer technology, less parts) so therefore would be cheaper to maintain and have a longer life-span
* Condensing boiler will save ~20% on my gas bill (~$300 savings annually). Cost of condensing boiler and installation is ~$4500 more then a non-condensing boiler, which is a 15 year payback. I'm not confident that the condensing boiler will last that long.
My questions are:
1. My local Home Depot, Rona, and Lowe's doesn't sell non-condensing boilers. Will it be difficult to find parts to fix a non-condensing boiler within the next 30 years?
2. I turn the heat on for only 4 months of the year. Does this damage the boiler in any way as the system sits idle for most of the year?
3. What should I be looking for in between different non-condensing boiler? Are there certain features I should be looking for? Should I be looking for an stainless steel heat exchanger?
|
Post Reply
|
Author:
NoHub (MA)
non-condensing boilers don't have the Federal hi-eff rebate of $2,750 so subtract that from your $4,500 number and your looking at less than six years, I could show you the numbers that it will take way less than that. The 600 lbs cast iron monster will not walk itself down into your basement (4 men minimum a 1/2 day each ) all by itself. In my eyes the home centers are the last place to buy a heating system. Cast Iron boilers are a thing of the past. Yes they are simple and will last longer but you pay for it. Don't get me wrong, If you have a ci-boiler and it's in good condition stick with it.
Edited 2 times.
|
Post Reply
|
Author:
DorkyJen492 (WA)
I actually live in Vancouver, BC, and am eligible for $1000. I have factored this into my $4,500.
My machinal room is on the ground floor, adjacent to my garage.
What is a CI boiler? Is this a non-condensing conventional boiler? If so, mine is not in working condition and needs to be replaced.
Do you know roughly how much longer does a non-condensing boiler last when compared to a condensing boiler? Would the maintenance fee also more expensive for a condensing boiler?
|
Post Reply
|
Author:
NoHub (MA)
Ci is (cast iron). Condensing Boiler's shine in climates like yours. Now if you can simply wheel a ci boiler into place than do it. unfortunately you might have a Problem Finding a Plumber that will install something you purchase yourself, I stopped doing that 25 years ago because I can't and should not have to warranty the customers boiler. Saving $500 or $600 now sounds great until it breaks down in the middle of the night.
|
Post Reply
|
Author:
DorkyJen492 (WA)
Why does a condensing unit shine in Vancouver's climate?
|
Post Reply
|
Author:
bernabeu (SC)
because of the 'latent heat' of water:
for every pound of condensate 900+ btus are 'recovered'
or
for every gallon, 7500+ btu
however
it takes 1,700 pounds of steam to make 1 pound of water
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Edited 1 times.
|
Post Reply
|
Author:
supolten (AL)
30 years of work ! Why is such a technique so rare now? If I were you, I would try not to save on the boiler and choose something of the highest quality and convenient. So that you don't have to replace it after installing it. When I needed to buy a similar technique, I turned to [dynamicpg.com.au]. They helped me pick up really high-quality equipment. In addition, they are engaged in maintenance, installation and repair of such equipment, which makes me very happy. It is easier to order everything from one company.
Edited 3 times.
|
Post Reply
|
Author:
bernabeu (SC)
because the 'big box stores' have brainwashed the consumer into 'never stop improving'
the 'technique(s) is/are still in use by the informed and the 'wealthy' who live in homes 'specced' by archichitects
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|