Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
geekintheyellow (MA)
Hi all!
Here's a photo of what's going on under my sink: [ibb.co]
This is my first time swapping out a kitchen faucet on my own. I could use some advice on how to deal with the bends in these supply lines (if I need to do anything to them at all). From some online searching, I know that it's best not to have any bends or kinks in the supply line, and to swap out the lines for a shorter line that can make a straight connection, or a longer line that can create a smooth loop over itself.
If the advice is to sort out the bends, I have a couple of road-blocks/questions:
1. The lines feed up into a single handle faucet head and it's not clear to me out to swap out the lines completely. I'm also having trouble finding resources online that show how that's done (if it's possible). Any advice?
2. If it's not possible to swap out the lines completely, can someone advise me on what kind of connector I'll need?
Thank you!
|
Post Reply
|
Author:
steve (CA)
The faucet end of the hoses are going to be specific to the faucet manufacturer and getting hoses of a different length might not be possible. The current installation has the hoses installed with sweeping bends and I see nothing wrong with it.
|
Post Reply
|
Author:
bernabeu (SC)
sweeping bends are fine and dandy
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
hj (AZ)
KInks and square turns, are one thing. Long sweeping bends or curves are something else, and there is seldom any problems with them.
|
Post Reply
|
Author:
sum (FL)
What about loopy bends and figure 8 bends?
|
Post Reply
|
Author:
bernabeu (SC)
the point is no kinks and minimum to no stress on the pressed ends
exactly the same as ANY plumbing installation
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
geekintheyellow (MA)
THANK YOU! Very helpful.
Now I just need to figure out how to reinforce the base. Every time I pull down the faucet head, the whole thing tilts forward a little, even though it is very tightly threaded to the base below and secured with silicone caulk. I think it's because my sink is made out of very thin sheet metal, and the faucet is anchored through a single hole.
|
Post Reply
|
Author:
hj (AZ)
I am having a hard time figuring out how the faucet is secured. Normally, there is a "flat" plate under the sink to prevent that.
|
Post Reply
|
Author:
bernabeu (SC)
hj,
unfortuneately in today's 'never stop improving' world here are MANY s/s sinks installed having such THIN 'skin' that sink itself flexes under the weight of the 'modern' high arc spouts (especially those with 'pull out or down' sprayers)
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|