Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
RR60 (VA)
Slab house. Has a 2" cleanout ABS, that is recessed in the block about 2". Can't get a wrench on it.
Do they make a square socket?
Also don't see a way to do it right and extend it out 1 1/2" to 2" without it sticking out to long.
Any suggestions?
Thanks
|
Post Reply
|
Author:
packy (MA)
be cheaper to just drill a couple of holes in it and then cut some slots and take it out in pieces. probably buy a new 2 inch plug for less than a buck.
|
Post Reply
|
Author:
hj (AZ)
Get a piece of square tubing with the correct inside dimension.
|
Post Reply
|
Author:
george 7941 (Canada)
Square sockets are available but they are expensive. Frequently they come as 8 point sockets.
hj's suggestion makes the most sense. Just go to a metals dealer and get a short length of square tubing.
Edited 1 times.
|
Post Reply
|
Author:
sum (FL)
I probably would use a chisel to strike a dent on the cleanout somewhere close to the edge, then use a flat head screwdriver and a hammer to hit it on a skew and see if it moves. If you end up cracking or punching through its a cheap item to buy new.
|
Post Reply
|
Author:
hj (AZ)
That is very difficult to do when the plug is recessed into a wall and the opening in the wall is the same size as the plug's o.d.
|
Post Reply
|
Author:
aaron.d.hess (PA)
what would macguyver do? This is one of those fun problems to have. get a piece of 2x4 and hog out the end with a sawzall to the dimension you need. there's your wrench.
|
Post Reply
|
Author:
hj (AZ)
1. The 2x4 would NOT fit the hole in the wall
2. If the plug is tight enough the 2x4 would split
|
Post Reply
|
Author:
Don411 (IN)
Could probably get an adjustable wrench on the plug, with the wrench vertically on the plug and sticking out of the hole. Then put a second adjustable wrench on the handle of the first one at 90* to get turning leverage. Might work in a pinch, but the square tubing is your best answer.
|
Post Reply
|
Author:
bernabeu (SC)
probably could use a basin wrench with minimum 'chipping out' for clearance
handy tool to have anyway
buy quality
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Edited 2 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor: