Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
sum (FL)
In general do you prefer using a push down drain (the one that you push down to open and push down again to close) or the traditional lift rod - pivot - pop up drain?
I am going to be installing a new faucet (Kohler) on a pedestal sink, and I can use the lift-rod pop up drain that comes with it. However, I also have a few push down drains laying around that I could use. Which is better?
|
Post Reply
|
Author:
packy (MA)
if you are buying a kohler bathroom faucet it will come with a pop up assembly. it should be brass and a decent quality. i would use it.
100 % silicone under the flange and around the rubber gasket below. you do NOT want a slight leak under a pedstal.
|
Post Reply
|
Author:
bernabeu (SC)
packy,
if one buys a kohler 'off the shelf' at a big box store it probably will have a 'cheapo' flat PLASTIC drain assembly including the piece which mates to the basin
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
hj (AZ)
When it comes time to remove the accumulated hair, the pop up will be easier.
|
Post Reply
|
Author:
m & m (MD)
I prefer the pop-up because I don't like sticking my hand in whatever was collected in the bowl to release it to the drain.
|
Post Reply
|
Author:
packy (MA)
bernabeau, i don't mind using the cheap plastic pop-up assembly on a vanity. it is easy to change in the future.
BUT.. on a pedestal.. NEVER..
kohler, a once great quality company has sadly fallen by the side of the road.
|
Post Reply
|
Author:
sum (FL)
packy, it does come with a brass drain assembly. I just thought the lift-rod pivot mechanism may be outdated. Some time back I bought a few push down lav drain by Decolav, thinking of using those instead of the pop up drain assembly that comes with a faucet simply because it is less cluttering under the sink, and sometimes those lift rods come loose and you need to get under the sink to tighten.
|
Post Reply
|
Author:
sum (FL)
oh I wasn't thinking about cleaning the hair out. That's a good point.
How would you remove the push down drain stopper? There must be a mechanism?
|
Post Reply
|
Author:
bernabeu (SC)
sum,
go pop-up
if this is for YOUR use don't 'trap' the pop up with the rod, merely place it ON TOP of the rod
the 'rod through the hole' design was an 'anti tamper/loss' design
look at the bottom of the pop-up piece and you will see the 'curve' designed for resting on top of the rod
(unless it is a 'twist and remove' type)
packy,
the plastic drain has a 'flat' top which will trap a puddle on 'thick wall' basins
the brass is the 'old school' curve design
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
sum (FL)
bernabeu I have never tried not threading the pop up through the rod. I will try it and see how it works, thanks.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|