Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
greg7mdp (MI)
Hi,
I'd like to replace my kitchen faucet, but I'm not sure how to remove the old one (just the rusted part that attaches it to the counter). Please see picture below. Can anyone tell me how it's done?
Thanks!
|
Post Reply
|
Author:
packy (MA)
the hex shape piece with the drop of water on the bottom unscrews. then the washer above it will drop down and that's it.
|
Post Reply
|
Author:
greg7mdp (MI)
Thanks Packy!
Edited 1 times.
|
Post Reply
|
Author:
george 7941 (Canada)
"the hex shape piece with the drop of water on the bottom unscrews"
Ha, ha. From the looks of it, it will snap before it unscrews. It does not matter if it snaps since you are changing the faucet anyway.
|
Post Reply
|
Author:
hj (AZ)
before you try to unscrew it, there is a "bolt" with a screwdrive slot in it up inside that piece jamming it so you have to loosen that first then the hex will unscrew.
|
Post Reply
|
Author:
m & m (MD)
To me, it looks like your best tool to use is something with an abrasive wheel.
|
Post Reply
|
Author:
packy (MA)
the 'stud' with the screwdriver slot will either unscrew with the hex piece or stay in place as the hex piece unscrews from it.
|
Post Reply
|
Author:
bernabeu (SC)
use a socket and simply unscrew the 'hex shaped piece'
if the stud snaps, so be it
FAUCET BE-GONE
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
greekguy7 (IL)
Anyone ever just take an angle grinder to the faucet body from the top in order to remove it, instead of crawling under there and wrestling with old rusted bolts? Just wondering....
|
Post Reply
|
Author:
srloren (CA)
Seems like making a mess to me. There should be more pressure from the Trades on the Manufacturers to be creative and make it much easier for these installs. My vocabulary gets out of hand when I have to install in these tight conditions. The lengthing of the nut and enclosing a plastic wrench by some manufacturers is a giant leap forward, but like I say the engineers/designers need to be more creative i.e. like some have lengthened the connectors so you don't need to tighten the connector in a tight spot. Reminds me of (George Clooney) in Brother Where Art Thou.
|
Post Reply
|
Author:
North Carolina Plumber (NC)
I've never used an angle grinder, but I have used a sawzall several times. Usually on Delta 400's when the bolt that drops thru the base and thru the sink turns all the way thru. I just saw the head off and watch the bolts drop to the bottom of the cabinet.
|
Post Reply
|
Author:
m & m (MD)
Done the same with the Delta 400 but it takes surgical precision- one bad move could be a new sink for the h/o at your expense.
|
Post Reply
|
Author:
hj (AZ)
Peel the chrome deck plate back and drill down through the center of the retainer bolt's head.
|
Post Reply
|
Author:
george 7941 (Canada)
I have used an angle grinder to take off the top of a faucet, not because I did not want to crawl under the sink but because the under sink fasteners were so badly corroded that they would not come off. As already mentioned there is a big risk of damage to the sink.
|
Post Reply
|
Author:
lnbonacci (CA)
Thank you to everyone on this thread. I had the same problem with a lot of rust and I wasn't sure how to get the faucet apart. Using a 12mm wrench the post turned easily and everything was easy from there.
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|