Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
pas_plombier (Non-US)
How do I unlock this thing?
I need to connect a dishwasher drain hose into that. I tried pulling and twisting with a clamp but nothing seems to move. It seems glued. I am afraid of breaking something.
Any clue?
|
Post Reply
|
Author:
bernabeu (SC)
It IS glued.
either
the hose fits and is then clamped
or
the piping will require modification
BY AN ACTUAL PLUMBER
(since you are asking)
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
pas_plombier (Non-US)
What "is glued"? What part should I twist or pull?
|
Post Reply
|
Author:
pas_plombier (Non-US)
There is no hole into that, so of course the drain hose doesn't fit right now.
|
Post Reply
|
Author:
packy (MA)
just cut off about 1/2 inch leaving enough for the hose to slide over and secured with a hose clamp.
if the hose is too small to slide over then you need a 'dishwasher to disposer' connector.
|
Post Reply
|
Author:
pas_plombier (Non-US)
So I need to cut 1/2 an inch with a saw?
Thanks for your answer Packy.
Edited 1 times.
|
Post Reply
|
Author:
KCRoto (MO)
I guess I've never seen a barbed fitting that didn't have a hole in the end. Seems like a foolish way to make a fitting; an unsuspecting person would have had a flooded kitchen because of that.
|
Post Reply
|
Author:
pas_plombier (Non-US)
Here it is from another angle.
So, I just cut it off with a saw?
|
Post Reply
|
Author:
packy (MA)
KC, i guess it comes the same way the nipple on a disposer comes plugged. it is there to use if you need it or to just look at and admire if you don't need it.
|
Post Reply
|
Author:
KCRoto (MO)
yeah, cut off as little as possible so you can keep the tapered point on the end. It is easier to push tubing on if the taper is there.
|
Post Reply
|
Author:
packy (MA)
yeah, and also smooth the inside of the end with a knife so there are no sharp edges to catch debris.
|
Post Reply
|
Author:
pas_plombier (Non-US)
Thanks for your replies, guys!
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor: