Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
trexmon (PA)
Outside water faucet broken. Not just washer as handle keeps spinning when trying to shut off. Can't find exact replacement for handle. Read how to replace faucet but pipes leading to faucet are inside a wall behind dishwasher, etc. Only about 1-2" sticking out outside soldered on and too close to siding to heat up. Any ideas?
Hopefully added a picture.
Edited 1 times.
|
Post Reply
|
Author:
m & m (MD)
There is enough pipe protruding from the wall that the old one can be unsoldered and a new one soldered on. Better yet, solder on a female adapter and then screw a hose bib that is male threaded.
|
Post Reply
|
Author:
North Carolina Plumber (NC)
A wet cloth could be placed against the siding if you're concerned about melting it. I'd sweat that valve off and sweat a female adapter in it's place and screw in a male boiler drain . There should be a vacuum breaker on the boiler drain.
|
Post Reply
|
Author:
trexmon (PA)
I heated the crap out of the fitting and will not budge. Been there for 25 years. Thought about cutting it off with a dremel but won't be enough left to sweat w/o setting vinyl on fire.
|
Post Reply
|
Author:
steve (CA)
How about cutting off most of the valve, leaving the threads? This way it takes less heat to loosen the soldered remains.
|
Post Reply
|
Author:
KCRoto (MO)
Use mapp gas. Propane may not be hot enough in the open air outside to get the job done if there is a breeze.
|
Post Reply
|
Author:
trexmon (PA)
How do you guys feel about Shark bites for this application. I could cut it off & have enough room for that. Steam coming out as I heat up. Maybe water causing desolder problem?
|
Post Reply
|
Author:
KCRoto (MO)
If you have steam, then you have water standing in the pipe and it is sloped the wrong way. In the long term, you would be better served by replacing the line from the inside and changing the slope of the line, but if it has (and you use) an inside shutoff, then it should be fine.
|
Post Reply
|
Author:
trexmon (PA)
25 years never shut it off & never froze. (knock on wood) Big problem is all pipe is inside wall.
|
Post Reply
|
Author:
packy (MA)
use a shop vac to get all the water out of the pipe. it will then unsolder easily..
|
Post Reply
|
Author:
hj (AZ)
YOu are not getting all the water out of the valve, because of the way it is constructed water stays in the bottom portion of it.
|
Post Reply
|
Author:
trexmon (PA)
Will try the shop vac tomorrow. Thanks
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
cut the valve off with a saw-zall as close as comfortable
water will then drain and you will have less 'heat sink' mass
easy peezy
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|