Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
Bobrob33 (KY)
How should I approach this?
Edited 1 times.
|
Post Reply
|
Author:
Fixitangel (NC)
Use some minimal expanding foam to seal around the pipe, and Gorilla glue to hold the flange to the brick, gently put screws in after setting for decoration? Wear Gloves.
|
Post Reply
|
Author:
KCRoto (MO)
How big of a void are you looking at? How deep is the void from the back of the sillcock to the inside of the wall? If it is one brick, I would cut a piece of plywood to fit in behind and get some long deck screws to anchor to the wood. Cut the wood with a hole in it to go around the sillcock (or a U shape to saddle it). Spray your foam inside, and secure the wood against the back of the brick, even with duck tape. Screw the sillcock down so it pulls tight, and the foam will keep expanding to fill in the void. Use the rest of the can to fill in any voids where air can get into your basement while you're at it, that stuff doesn't save well.
|
Post Reply
|
Author:
North Carolina Plumber (NC)
I'd fill the void in the brick with hydraulic cement and use tapcons to secure the faucet.
|
Post Reply
|
Author:
kenplumb67 (RI)
I would second North Carolina plumber's advice
|
Post Reply
|
Author:
Bobrob33 (KY)
I've already installed the faucet and dont have much space behind there. Can I like, squirt the hydraulic cement in? Is there any that is pre mixed or anything?
Thanks for the great suggestions!
Edited 1 times.
|
Post Reply
|
Author:
packy (MA)
if you are going to use hydraulic cement, you might as well chisel out a small amount of brick so you can get enough cement into the opening.
|
Post Reply
|
Author:
KCRoto (MO)
I would stick with foam or caulking. I wouldn't want to have to chisel out the wall because someone forgot to take the hose off and this one gets busted.
|
Post Reply
|
Author:
Bobrob33 (KY)
I've only ever had experience with the foam when I had to remove some from somewhere, but would it be enough to hold the pipe steady?
|
Post Reply
|
Author:
KCRoto (MO)
It will keep it from flopping around in the hole and getting damaged, and it will stop any air from leaking around it.
|
Post Reply
|
Author:
Christopherd74 (AL)
if you are going to use hydraulic cement, you might as well chisel out a small amount of brick so you can get enough cement into the opening.
[www.kitchenfaucetreviewsonline.com]
Edited 1 times.
|
Post Reply
|
Author:
Paul48 (CT)
Make sure that any foam you use is closed-cell, or it will soak up water like a sponge. I think most of the foam in a can stuff is open-cell.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|