Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
Arch (Non-US)
Hello new friends!
Archie here. I sure could use some professional help with the installation of a new shower I'm constructing in my basement!
I have 3/4" supply lines feeding a aqua brass 3003 thermostatic valve with 3/4" supply into the valve with 4 3/4" out lines. witch will feed 3 body jets on either side of stall,also a rain shower head, & a hand held sprayer. I'LL be using 3/4" lines to feed all mentioned. Ive seen several ways on how to loop the body jets my concern is do all veriations of on how to loop jets by reputable refrences give the same amount of equal pressure, or is there a spacific method to ensure equal pressure when contructing a new shower system from scratch?
THANKS FOR YOUR TIME FOLKS! HOPE YOU CAN HELP OUT!
"ARCHIE"
|
Post Reply
|
Author:
KCRoto (MO)
The heads themselves have flow restriction so it maintains equal pressure in the system that keeps all of the jets at or about the same pressure.
|
Post Reply
|
Author:
Arch (Non-US)
THANKS MY FRIEND!!!!!!
Edited 2 times.
|
Post Reply
|
Author:
packy (MA)
archie, so much depends on the location of the 3 body sprays.
personally i would run 3/4 out of the control valve and branch off 1/2 inch to each spray.
each spray is limited to 2.5 GPM so you should be fine.
keep the number of elbows to a minimum on the farthest spray.
make sure to set one of the sprays at a height where it will hit you just above the base of your spine. right where we all get backaches..
also, running 3/4 to the hand held is overkill.
lastly, make sure when choosing a shower drain choose one that takes into account the extra volume you will be creating. they are made for that purpose. you don't want to be standing in ankle deep water..
|
Post Reply
|
Author:
hj (AZ)
If the heads are stacked one above the other, I go straight to the middle one and tee up and down to the other two, without a "pressure balancing loop?.
Edited 1 times.
|
Post Reply
|
Author:
packy (MA)
here we go again...
quote "witch will feed 3 body jets on either side of stall"
after re-reading this part, does this mean 6 sprays total or 2 on one side and one on the other?
|
Post Reply
|
Author:
North Carolina Plumber (NC)
If the poster is using correct grammar, then there will be 6 body jets.
|
Post Reply
|
Author:
packy (MA)
then if there are 6 sprays, 3/4 plastic won't be big enough. would have to use 3/4 copper.
if the shower valve and diverter are located on the back wall of the shower then it would be easy to design a loop in the long wall. put three 3/4 by 1/2 tees stacked on each vertical pipe
of that loop.
|
Post Reply
|
Author:
hj (AZ)
3, 6, or 9, it would be immaterial, each grouping would be assembled the same way with a feed from the control valve. A balancing loop would be superfluous.
|
Post Reply
|
Author:
packy (MA)
most control valves do not allow multiple outlets to function simultaneously. so he would have to choose which set of 3 sprays he wanted to use rather than using them all at the same time.
|
Post Reply
|
Author:
Arch (Non-US)
did'nt mean to frustrate anyone!
There are 6 in total 3 per side.
|
Post Reply
|
Author:
Arch (Non-US)
Hello sir,
using this design by teeing off the center jet."provide better pressure" over the loop design,& all the elbows it envolves wich must restrict flow,(apposed to your design without all the elbows)
THANKS FOR YOUR INPUT!!!
"ARCH"
|
Post Reply
|
Author:
Arch (Non-US)
Thanks for your help!
Q.is there body jets,or sprayers on the market place that have less than 2.0 gpm
Edited 1 times.
|
Post Reply
|
Author:
North Carolina Plumber (NC)
Delta 501000 uses 1.8 GPM.
Hansgrohe 06342000 uses 0.8 GPM.
Edited 1 times.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|