Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
herbeapuce (NY)
I'm just curious....
it's obviously wider that 1/8 " ???
why is this called 1/8" MIP then ?
thank you.
|
Post Reply
|
Author:
Paul48 (CT)
MIP is male iron pipe, which that isn't. Nor is it 1/8". Maybe I'm all wet. They've kind of made MIP interchangable with NPT, but that's not 1/8".It is just what has been accepted as 1/8" pipe. How's that for babbling?
Edited 1 times.
|
Post Reply
|
Author:
KCRoto (MO)
Most importantly, the bag says nipple on it. :p
|
Post Reply
|
Author:
steve (CA)
Dates back to when the only metal available(readily available?) for making pipe was cast iron. In order to get the pipe to withstand the pressures being used, the pipe wall needed to be very thick. So, as metal science evolved and stronger steel pipe became available, the need for the thick wall diminished, but a standard needed to created. It was decided that the "standard" OD, used the early thick walled cast iron pipe, would be kept and the ID would vary.
|
Post Reply
|
Author:
hj (AZ)
Because the i.d. is 'nominally' 1/8". Although that "looks" more like a 1/4" nipple.
Edited 1 times.
|
Post Reply
|
Author:
herbeapuce (NY)
all right . Thank you guys.
it is already so complicated to choose the right fittings, they should get rid of this nomenclature system IMO
thanks
Stef.
|
Post Reply
|
Author:
hj (AZ)
quote; they should get rid of this nomenclature system IMO
And what would you replace it with? "I want a piece of pipe slightly smaller than my little finger"? A better question is "What were you doing that even needed a 1/8" nipple", because that is a very rare size.
|
Post Reply
|
Author:
KCRoto (MO)
I used one to make a dynamic pressure test apparatus for a sloan valve. It took a couple years to find one of the old style tops that has enough brass to thread into.
|
Post Reply
|
Author:
herbeapuce (NY)
Quote: "And what would you replace it with?" end of Quote.
About real OD, real ID, and thread size..... wouldn't that makes more sense
thanks
stef
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|