Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
hj (AZ)
That words, as does a 5 foot piece of pipe, or a big hammer. It all depends on how much access you have.
|
Post Reply
|
Author:
bernabeu (SC)
HAH
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Edited 1 times.
|
Post Reply
|
Author:
m & m (MD)
Bern, did it loosen?
|
Post Reply
|
Author:
hj (AZ)
That is how my dad threaded 2" pipe with a "block die".
|
Post Reply
|
Author:
hj (AZ)
A VERY good way to do a "face plant". Especially, since that is tightening it.
Edited 1 times.
|
Post Reply
|
Author:
bernabeu (SC)
m & m;
I believe the earth rotated around the pipe!
The longest lever I actually used was a 10' length of 3" on a 4 foot with both me and my 6'6" helper 'bouncing' the end ~ we were unscrewing an old 2" wrought iron gate valve from an A-106 pipe !
? Why did we not simply cut it off with a SawZall ?
Probably because we were young and very very stupid !
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
Fixitangel (NC)
If you want to make that fitting loosey-goosey; I would use a 10 foot cheater pipe and a little dab of this stuff:
Works for me.
|
Post Reply
|
Author:
greekguy7 (IL)
Aren't you worried that all that force and pressure would break something else on an old piping system instead of the specific threaded joint you wanna take apart?
Is it better sometimes to give it a few hits with a 5lb. hammer instead of more leverage?
|
Post Reply
|
Author:
bernabeu (SC)
whatever unscrews - unscrews
if it breaks - it was already weak and 'ready to go'
whatever we break we will fix
? how would YOU take it apart ?
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
|
Post Reply
|
Author:
hj (AZ)
quote; Is it better sometimes to give it a few hits with a 5lb. hammer instead of more leverage?
Sometimes it is "AND" not "instead of". WE do whatever it takes because as bernabeau says, "If we break it we fix it".
|
Post Reply
|
Author:
sum (FL)
I think also at some point it is no longer 100% about solving that problem but gets personal between you and the stubborn joint. You want to take it apart mano o mano and resorting to a saw is an admission of defeat.
|
Post Reply
|
Author:
hj (AZ)
It also means you have to rethread the pipe.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor: