Over 698,000 strictly plumbing related posts
Plumbing education, information, advice, help and suggestions are provided by some of the most experienced plumbers who wish to "give back" to society. Since 1996 we have been the best online (strictly) PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't tract you. We absolutely do not sell your personal information. We are made possible by:
Author:
Eric23224 (VA)
I just want to say that I've been a longtime lurker of this forum & you guys are great help.
A family member & me are having a problem installing my hot water heater. We got it in and connected everything but there is ONE thing: a small leak where at the top near the adapter. I dont know what exactly this adapter is called so I could not look it up, & I am having a hard time taking it off.
h t t p://i.imgur.com/pMEDqBw.jpg
I cant post links yet, but heres a pic
Any solution or help in how to stop this little leak would be appreciated.
I bought it used from a friend who was selling his house, its only 3 years old. I am a little strapped at the moment, or else I would have bought a new one.
|
Post Reply
|
Author:
bernabeu (SC)
how to link to image: [www.plbg.com]
that is a pipe thread X solvent weld adapter fitting
you will need a solvent weld (glue) coupling for the tube above the fitting as the tube will have to be cut then coupled back together
the adapter needs to be replaced as the glue end can NOT be repaired
then the tube above gets reconnected with the coupling + a short 'filler' piece
if you have some 'give' in the piping you can cut flush to the adapter and reinstall w/o the coupling
about 35 cents for the coupling, $1-2 for the adapter, + $2-4 for the glue and primer
buy the smallest cans you can get as it has a limited shelf life after opening
see: [www.bing.com]
==============================================
"Measure Twice & Cut Once" - Retired U.A. Local 1 & 638
Edited 5 times.
|
Post Reply
|
Author:
packy (MA)
better check local codes. in MA, plastic pipe is not allowed within 18 inches of a water heater.
must use metal and transition at the legal distance.
|
Post Reply
|
Author:
m & m (MD)
Packy- gas, yes. But even on electric?
|
Post Reply
|
Author:
North Carolina Plumber (NC)
Water heater flex with a built in gatorbite on the end. That would take about 1 minute to make the repair. No glue, no drying time, code approved, etc.
|
Post Reply
|
Author:
packy (MA)
m&m, yes, even on electric. even on superstor as well.
first 18 inches of pipe (cold or hot) must be metal.
|
Post Reply
|
Author:
hj (AZ)
Electric heaters get just as hot as gas ones.
|
Post Reply
|
Please note:
- Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
- Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
- Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
- Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.
Search for plumbing parts on our sponsor's site:
Special thanks to our sponsor:
|